How to clean hot tub filters: what you need to know

How to clean hot tub filters: what you need to know

People who possess a hot tub in their garden will tell you that it is a true joy and a wonderful luxury to be able to jump in at the end of the day and let the whirling water melt away all the tensions of the day. You can take advantage of those relaxing waters every day if your hot tub filter is suitable and is cleaned frequently.

The filter cartridge for hot tubs is likewise built-in. To ensure that the water you bathe in is clean, this helps separate dirt and bacteria from it. You may prolong the life of the filter by occasionally cleaning it. Because buying a new one maybe a bit pricey, simply cleaning it could help you save a little more. Nevertheless, if you have extra money and are feeling like lavishing, then by all means, purchase a new one.

Filters keep the hot tub running smoothly while maintaining the water in the bath clean. Since unwanted compounds like oil, grime or hair will contaminate the water, a blocked or damaged filter can be disastrous. By dumping less waste, you will be able to save money while simultaneously reducing your impact on the environment. It will be straightforward to maintain a hot tub filter once you know how to.

You don’t need so much stuff from everywhere! Let’s keep it short and simple. Chlorine bleach, a soft scrub brush, and a power washer are all you need.

Once everything is ready, just carry out these easy steps:

Step 1: Ensure that you turn off the heater before removing the filter. This will safeguard you from any accidents. Of course, you wouldn’t want to be electrified.

Step 2: Check the valves at the bottom of your tub. Just below the skimmer, there is a pipe that may be found between two valves. The filter is situated in this area. While some filtration systems are simpler to operate, some tubs use filter that need you to twist the bottom of the filter in order to remove the cartridge.

Step 3: Using a light scrub, remove hair and dirt from the area. By brushing the filter along the seams, make an effort to get rid of as much dirt as you can. Don’t brush too vigorously, or you risk damaging the filter of delicate, ultra-fine particles. You can soak the cartridge first in warm water and then add a few drops of white vinegar if it is tough to remove. The filter’s lime deposits will also be eliminated by doing this.

Using filter cleaner wand

Step 4: The baking soda approach can be used to whiten your filter. Simply combine baking soda and water, then immerse the filter for a few minutes in this mixture. Likewise, this will automatically dislodge any debris and get rid of any leftover particles.

Step 5: Make sure to use a low-pressure washer to avoid damaging the filter. You can use a standard garden hose fitted with a pressure nozzle set to a low level if you don't have a power washer. Spray at a 45° angle down the filter until the water is clear. For added stability while washing, insert a broom stick into the canter of the filter.

Step 6: Add 3 gallons of boiling water to 1/4 cup of chlorine bleach. Spend some time soaking the filter in the mixture. This will assist in eradicating the bacteria and whitening the filter.

Soaking the filter Rinsing the filter

Step 7: Utilizing a hose and running water, thoroughly rinse the filter. Ensure that water is used to remove all chlorine bleach residues.

Step 8: To ensure that the filter is completely dry, you can leave it in the sun for a few hours. Once dry, install the filter back in its original position. Make sure to close the lid of the hot tub to prevent any dirt or debris from getting inside.

Return it in the same manner in which you took it out. To prevent filter tube leakage, snugly tighten it. Look for any wear or damage indications. If there are any, replace the filter tube with a new one. Finally, test the system to ensure it works correctly.

Final thoughts

Before water is pushed back into the water through the jets, heated by the heater, and then pumped through the pump, a hot tub filter's function is to filter any contaminated water. Clean, warm water for your hot tub is provided by this circulation.  The filter is the first step in maintaining a clean hot tub.

So, your hot tub filters should be cleaned at least every three to four months to ensure the water stays clean and safe for use, or more frequently if the tub's load is particularly heavy, to guarantee their longevity.

Additionally, depending on how well the spa has been taken care of and how frequently it is used, it is advised to replace the filter every year to year and a half. The filter may need to be replaced sooner than you anticipated if there are any indications of cracking or physical damage.

Enjoy your hot tub and maintain it in fantastic form, with a little maintenance to keep you in great shape as well!